How To Make "PILCHARD RINGS"

Post Reply
ez2cdave
Fisher
Posts: 33
Joined: Sun Feb 08, 2009 4:24 pm

How To Make "PILCHARD RINGS"

Post by ez2cdave »

How to make pilchard rings

To All,

When I was growing up in South Florida, I used Pilchard Rings ( aka - "Ribbon Rigs" ) to catch baitfish ( Pilchards / Menhaden ) from the fishing piers . Recently, I discovered that they have been declared to be a "gill net", theoretically "illegal", and not available in stores anymore. I always used to make my own, as a kid.

So, for purely "historical value" . . .

"HOW TO MAKE PILCHARD RINGS"

MATERIALS :

6 ft. of #7 Dark-Colored, Solid Leader Wire

1 Barrel Swivel

1 Snap Swivel ( to allow weight changes )

Cardboard Toilet Paper or Paper Towel Tube ( 1" I.D. Sch. 40 PVC works great, too )

3 ft. of Bright Red Ribbon ( 3/8" - 1/2" wide )

Pyramid, Bank, or Dipsey/ Bass Sinker ( 3/4oz - 1 1/2oz +/- )

CONSTRUCTION :

(1) Start with a six-foot length of No. 7 dark leader wire.

(2) Bend it in half and slide on a barrel swivel.

(3) Tie a LOOSE, TWO-TURN, overhand knot in the wire near the bend to "capture" the swivel

(4) Form a loop, using a the toilet paper or paper towel tube ( or 1" I.D. Sch. 40 PVC pipe )as a "mandrel" ( you may need to vary the loop size depending on baitfish sizes in your area) and make a SINGLE-TURN Overhand Knot,

(5) ALTERNATE the direction of the Overhand Knots each time to help the rig hang straighter

(6) Repeat until you have a series of loops, leaving a couple of inches of wire free at the bottom

(7) Slip on the Snap Swivel and connect the loose ends of the wire, using a SHORT Haywire Twist

(8) Hold the rig at each end and pull on it to stretch the loops out into an oval shape

(9) Attach the bright red ribbon at one end by knotting it to the Swivel loop

(10) Pass the ribbon through rings one-third and two-thirds of the way up the rig

(11) Attach the ribbon to the other Swivel, leaving some slack in the ribbon when fully extended

(12) Attach the Sinker to the Snap Swivel and the rig is complete

HOW TO USE:

Tie the rig to a light spinning rod and lower or cast it into a baitfish school and let it sink. You will feel baitfish hitting the rig. Keep the line tight and wait for the rod to bend. When it does, wait a few seconds and reel up. Remove baitfish and repeat, as desired !

User avatar
fishnfool73
AMBASSADOR to the... BF FORUM
Posts: 8703
Joined: Tue Nov 07, 2006 6:18 am

Re: How To Make "PILCHARD RINGS"

Post by fishnfool73 »

Those were great when targeting big pilchards for tarpon and snook. I still can't understand the theory behind them being illegal.
Dreaming the dream that one day I can be as good as some of the boatless pros and catch some 12 inch mangrove snapper.

ez2cdave
Fisher
Posts: 33
Joined: Sun Feb 08, 2009 4:24 pm

Re: How To Make "PILCHARD RINGS"

Post by ez2cdave »

fishnfool73 wrote:Those were great when targeting big pilchards for tarpon and snook. I still can't understand the theory behind them being illegal.

The "PETA-type", "Enviro-Nazi's" got them classified as "Gill Nets" . . .

Post Reply

Return to “Species info--Dedicated to Targeting”